Setting Up Wireless Router For Hughes Satellite Internet

The Internet Service Provider (ISP) HughesNet gives high-speed internet connection through the Satellite connection. The HughesNet satellite antenna should be placed in clear sight in the southern side of the sky at a distance of at least 4 feet from the ground. The HughesNet modem receives the satellite signal and delivers it to the device via wireless routers to setup Wireless Router For Hughes Satellite Internet. You can easily connect your wireless router to the HughesNet modem by using an Ethernet cable. Power up the router. Load the web-based setup page of the router and secure the internet connection with a unique network SSID and password. After securing the internet connection, you can connect your desktop computer, laptop, smart device, and tablet to it.

Connect HughesNet Commununication Satellite Internet

Make sure the HughesNet modem is installed properly with an antenna.
The antenna must face the south.
Turn on your HughesNet modem and router after connecting it to a power source and connect Wireless Router For Hughes Satellite Internet.
Unplug the Ethernet cable, if it is already plugged in.
Connect the router setup to your computer by using an Ethernet cable.
Access the router’s IP address on your computer’s web browser.
Log in to the router’s account by using the default username and password as mentioned on the label of the router or manual.
Locate the Network Settings of the router on the web-based control panel.
Reach the router’s control panel and change the Router IP Address to 192.168.10.1, and then save all the changes in the settings. Restart the computer.
Plug an Ethernet cable between your HughesNet modem and router.

Wireless Router For Hughes Satellite Internet

How to Connect a Router to HughesNet?

Connect the HughesNet modem to a power socket. Press the main power switch to supply power on the modem.
Plug the router’s power cord to the socket and turn it active. If the computer or laptop is not active, activate it from Sleep mode.
If the HughesNet modem and the router is already connected with an Ethernet cable, unplug it from both the devices.
Log in to the web-based control panel of the router. Set the IP address or WAN to a value greater than that of the HughesNet modem to setup Wireless Router For Hughes Satellite Internet.
For instance, if the IP address of the HughesNet modem is 10.200.1.33, then the IP Address or WAN is set to 10.200.1.34 while following How to Connect a Router to HughesNet.

Use the HughesNet modem’s IP address as WAN/Internet Default Gateway of the router. Set the WAN/Internet DNS server address of the router to 66.82.4.8 and 66.82.4.12.
Configure the LAN settings of your wireless router to operate it as a DHCP server. The configuration process may vary based on the router manufacturer and model.
Plug an Ethernet cable into an appropriate port on the HughesNet modem and to the WAN/Internet port of the router for HughesNet Commununication Satellite Internet.
Reboot your computer. Now the IP address of the computer is renewed and the computer or laptop gets access to the internet while following How to Connect a Router to HughesNet.
If the network connectivity fails, make sure that your computer’s network setting was configured in a way to obtain the IP address of its own.

How to Install a Netgear Router With Hughes Satellite?

HughesNet is the best choice in America for Satellite internet connection with 1 million active subscribers. This applies satellite technology to provide high-speed internet connection. It is available to customers with slow and super-fast options.

The IP address of the Netgear router and HughesNet modem are the same. Modify the IP address of the Netgear router to secure the HughesNet modem’s internet connection.

Unplug the Ethernet cable from the back of the router and modem. If the router and modem are previously connected, disconnect them.

Turn on a computer or laptop, if it is not active. With an Ethernet cable, connect your printer and modem and follow How to Install a Netgear Router With Hughes Satellite.

Plug in one end of the Ethernet cord to the appropriate Ethernet port on the back of the router. Link the other end of the Ethernet cable to the Ethernet port at the back of the computer or laptop.

Press the On/Off button on the router to turn it on. Enter http://192.168.0.1 on a new tab on your web browser.

When prompted to enter the authentication details, enter admin as the username. In the place of Password, enter a password. Select OK to log in to the web-based Netgear interface.

Click the Advanced tab on the left panel of the interface screen. Select LAN IP Setup.

Modify the IP Address to 192.168.10.1 and change the Starting IP Address to 192.168.0.2.

Change the Ending IP address to 192.168.10.51. Click the Apply tab to save all the changes that you have made.

Now some error messages are shown on the interface screen. They include Action Cancelled or Page Cannot be Displayed.

Close the browser and power off the network router. Plug the HughesNet Modem to the internal port of the Netgear router setup.

Turn the Netgear router active. Restart the computer or laptop on which the router is connected to setup Wireless Router For Hughes Satellite Internet.

When the computer turns on, type http://192.168.10.1 in the address bar of your web browser. Apply the default login credentials to log in to the web interface for HughesNet Commununication Satellite Internet.

Click the Setup Wizard tab on the left side panel of the interface page. Click the checkbox next to Yes and then choose Next by doing How to Install a Netgear Router With Hughes Satellite.

Select the Next option in the Dynamic IP Detected screen and click Apply.

How To Reset Your HughesNet Modem?

HughesNet, the major satellite internet service provider, covers about 50 states nationwide. If the Wireless Router For Hughes Satellite Internet modem faces any issues or the internet speed is too slow, then reset the modem settings.

Make sure the HughesNet modem is powered on and fully functional.
Disconnect the router from the back of the modem and plug any other connection cables except the power cable.
Find the WPS button on the front face of the modem.
On the rear of the HughesNet modem, locate the Reset button under the barcode.
Hold the WPS button on the HughesNet modem.
Push and release the Reset button with a pointy object while doing How To Reset Your HughesNet Modem.
Hold the WPS button until the LED’s on the front of the modem begin flashing.
The LED light might take about 30 seconds to start flashing.
To ensure that the Reset process is successful, log into the Web setup page of the modem with the default username and password.
Now the HughesNet modem settings are reset to default.

hughenset commununication satellite internet

How to Use Wireless Routers With Satellite Internet?

Connect the HughesNet modem to the power supply through a power cord and turn it on.
Turn the computer active and connect it with the HughesNet modem to setup Wireless Router For Hughes Satellite Internet.
Access the HughesNet modem’s web interface. Type the IP address as 192.168.0.1 in the browser's address bar and press Enter.
The HughesNet modem appears on the computer. Click the Red button under System Status.
Choose the Little man icon below the menu bar. Now the Advanced Configuration and Statistics window opens on the screen.
Click the Installation menu on the left panel of the screen and then select the Setup tab while following How to Use Wireless Routers With Satellite Internet.
Now the HughesNet Setup window opens. Click the Config File - Upload option. Choose the file from the computer and click Open.
Select Upload to start uploading the file. Now the HughesNet - Antenna Location page opens on the screen.
Click Next to proceed further and type the zip code where you have installed the antenna for your modem and select Next.
When the HughesNet - Satellite Parameters page opens, make an appropriate choice and click Next.
Choose the name of the Receiving LNB in the HughesNet - Receive LNB selection and click Next.
Select Display Signal Strength to view the signal strength and then choose Next.
Choose the Automatic or Manual option and then select Next.
Complete the registration process and restart the computer for HughesNet Commununication Satellite Internet.
Connect the HughesNet modem to the router setup and pair the computer with the router. Now you can access the internet connection on your computer.

Wireless Network Connection Problems With HughesNet (How to Fix)

The HughesNet Commununication Satellite Internet modem provides network connection through a satellite. Space-age technology communicates with the modem via a satellite Dish. While browsing through the HughesNet modem, the request is sent to a satellite in the space which is located 22,000 miles from the earth. In case the modem or computer fails to connect to the satellite internet, check the points below to resolve the Network connection issue.

Make sure the HughesNet connected to the power source.
Set up the antenna at an appropriate direction to receive signals from the satellite.
Based on the type of data (image, flash headers, or videos), the internet speed may reduce or increase.
Check the Transmit light on the modem and whether it is continuously blinking while you use the internet connection. A blinking light ensures that the modem communicates with the satellite.
Once the modem contacts and receives data through a satellite, the Receiving light starts blinking and the web page loads.
Check whether you have exhausted the limit of high-speed internet.
Buy another booster pack to retain super-fast internet network.
Check the speed of the HughesNet satellite internet through the HughesNet mobile app.
Storm or wind may affect your internet connection.
Check the Satellite Dish antenna outside and look for any leaves, debris or snow. Remove everything that obstructs the signal during setup Wireless Router For Hughes Satellite Internet.