If you want to resolve problems occurring in a Cisco router, you can reset it. Resetting router will bring back the factory default settings by following How to Reset the Cisco Router. All your customized settings get erased when you push the Reset button. After you reset the Cisco router, it is required to configure the router again. You can either use the reset button on the router or the router commands for this purpose. Remember that when you reset the router, you should set up it again by launching the Cisco configuration page. You can navigate to the Advanced Security tab to update new settings.
Switch off the Cisco router by pressing the Power button.
Now, plug the power cord to your router and the power supply.
Search for the Reset button on the router and proceed how to reset the cisco router.
The location of the Reset button changes depending on the Cisco router’s model.
Long press the Reset button while you push the Power button.
After 10 to 15 seconds, release the Reset button.
Wait for the router to complete the booting process.
When the lights on the Cisco router blinks continuously; it indicates a successful reset.
Switch off the router and wait for some time.
Turn on the Cisco router and proceed to configure it.
How to Reset a Cisco Router to Factory Default
When you reset the Cisco router, the customized settings will be erased. Resetting the router will bring back the factory defaults settings. After you reset the router, the configuration settings get reflected only when you restart it.
You can reset the router via the PuTTY app. You can also use the Command Line Interface to reset the router.
To reset the Cisco router through the Reset button, search for the button on the router. The Reset button is located at the rear side of the router. However, the location varies for different routers.
Long press the Reset button while you hold the Power button to turn it on. Release the Reset button and wait for a while. When the light on the router blinks, it indicates a successful reset. Now, power off the router and restart it again.
If the above process did not work out, you could reset the router through the Command Line Interface. Use a console cable to connect the computer and your router.
Power on the Cisco router if it is turned off. Wait for 10 minutes for the router Setup to complete the booting process. When the lights on the router blink continuously, it indicates a successful reset.
Start the terminal emulator program on your PC to access the command line interface (CLI). In the CLI screen, enter the following commands to erase the default settings.
Router --> enable
Router# write erase
[confirm] < Press Enter key >
Continue with reload? [confirm]
Wait for the Command Line Interface to display a completion message.
Now your router is successfully rebooted. Restart your Cisco router for the settings to get reflected by following how to reset the cisco router.
After resetting, launch a web browser on your computer and access the router’s web-based setup page to customize the settings. You can also change your router’s SSID and password after resetting it to safeguard your wireless network.
How to Reset Cisco 800 Series Router
To reset the Cisco 800 series router by following how to reset the cisco router, you can either use the PuTTY application or press the Reset button to restore the original factory settings. If you are using the PuTTY application, follow the step by step instructions given below.
Turn off your Cisco 800 series router and power it on after a few seconds.
If you are a Windows user, press the Ctrl and Break keys on the keyboard simultaneously.
If you are a Mac user, press Ctrl + A and then tap the Ctrl + B keys to launch a prompt for Cisco Wifi Router Reset.
Type confreg 0x2142 on the prompt to erase the customized settings on your Cisco router.
Followed by the above command, enter reset on the prompt screen.
Now, your Cisco router restarts. If you are asked for an initial configuration, type No while doing How to Reset a Cisco Router to Factory Default.
Press Return after the loading has completed to go back to the main prompt screen.
On the prompt screen, type en to go to the privileged mode and enter write erase to delete the customized settings.
Enter y and type configure t. Now, enter config-register 0x2102 and type end to complete the process.
How to Reset the Password on Cisco Router e1000
Resetting the Cisco e1000 can be achieved through accessing the router’s setup page. Reset the router’s password periodically to safeguard your wireless network.
Connect your computer or smartphone to the Cisco e1000 router’s network.
Open a search engine like Google Chrome or Mozilla Firefox.
In the Address bar, fill in the router’s default IP address and press the Enter key by proceeding How to Reset a Cisco Router to Factory Default.
The default IP Address for the Cisco router is 192.168.0.1.
You will be prompted to enter the details in the Login page that appears. Enter the login details such as username & password and click Sign In.
Enter cusadmin in the username field and type password in the corresponding field for Cisco Wifi Router Reset.
On the Cisco router’s page, click the Setup tab and navigate to the Pre-Shared Key field.
Click the Show Key radio button to find your existing password.
Type the new password in the Pre-Shared key field and select Save Settings.
Once you have saved the new password, you will be disconnected from the network.
Reconnect the computer or any other device to your Cisco e1000 using the new password.
How to Reset Cisco Linksys e1200 Wireless Router
After you reset the Cisco Linksys e1200 router, the settings get restored to the factory defaults. The guidelines on how to reset the Cisco Linksys e1200 access point are as given below.
The manual and software reset methods will help you reset the Cisco Linksys e1200 router by following how to reset the cisco router.
Software reset: Open the browser on the Personal Computer that is connected the Linksys Cisco e1200 router.
In the address field, enter your access point’s gateway IP address and then press the Enter button on your keyboard.
Once instructed, type the administrator credentials to sign in.
Click on the Administration tab on the web-based setup page of your Linksys Cisco e200 router.
Choose the Factory Defaults option and then select the Restore Factory Defaults button.
Hard reset: Find the Reset button on the Linksys Cisco e1200 router.
Long press and hold the Reset button for about ten seconds by making use of a pin or paper clip.
Disconnect the Linksys Cisco e1200 router from the wall socket for at least thirty seconds.
Replug the cord and do not proceed until the Power lamp turns solid; this completes the reset process.
How to Reset Cisco 1921 Router to Factory Default
Generally, there are two methods using which you can reset the Cisco 1921 access point to its factory defaults. The steps on how to reset the network router using the Reset button are given below,
Power Off the Cisco 1921 network router.
With the router turned Off, insert the electrical cord to its rear.
Attach the other end of the cord to a functioning power source.
Locate the Reset button on the Cisco 1921 router while following how to reset the cisco router.
Force press and hold the Reset button while you are turning On the wireless access point.
Wait for at least ten to twenty seconds and then release the Reset button.
Do not proceed for about five to ten minutes until the booting process gets completed.
Verify the lamps on your Cisco 1921 router.
If the lights on the router are flashing or solid in repeated patterns, it indicates that the booting is finished.
Turn Off the Cisco 1921 router, and the next time you switch it On, the factory default configuration will boot into the device.
How to Reset Cisco Router 1841
When you reset a Cisco 1841 router, all the data inside it gets deleted. The guidelines for resetting the Cisco 1841 router are given below.
Power On your Cisco 1841 router and do not proceed for a few seconds, and then switch it off.
Within the first thirty seconds of the startup, send a break character to the terminal.
For Windows Personal Computer, if you are utilizing PuTTY as the transfer app, press the Ctrl and Break keys on your keyboard simultaneously.
Else, right-click on the bar that is available on top of the PuTTY dialog box and then choose Special Command > Break.
For Mac computers, press the Ctrl + A keys on the keyboard.
Now, tap the Ctrl and B buttons, and a Prompt pop-up window will open on the desktop for Cisco Wifi Router Reset while following How to Reset a Cisco Router to Factory Default.
To inform the access point to stop the existing configuration on startup, type confreg 0*2142 on the Prompt screen.
Restart the Cisco 1841 router by typing the Reset command on the desktop. The Cisco 1941 will restart while following how to reset the cisco router.
Enter NO if you are instructed for initial configuration dialogue.
Once the loading has stopped, tap Return to go back to the Main window.
On the prompt screen, enter privileged mode by typing en. For issuing the erase command, type erase.
Enter y to confirm erase command. Now, type configure t and enter config-register 0*2102; this commands the Cisco 1841 router to process the existing configuration on startup.
Enter end and power Off the Cisco 1841 router.
After a few seconds, turn the router On and now the original settings will be restored on the device.
How to Reset Cisco Router 1941 to Factory Default
The how to reset the cisco router procedure to reset the Cisco 1941 wireless access point to its factory defaults using router commands is listed below,
With the Cisco 1941 router turned Off, attach the electrical cord to it.
Also, plug the other end of the electrical cord to a working outlet.
Link your computer or laptop to the console port on your Cisco 1941 router by utilizing the console cable.
Switch On the wireless access point and wait for approximately six to ten seconds until the device finishes the booting.
If the lamps on the router are flickering, it shows that the boot process is complete for Cisco Wifi Router Reset.
Begin the terminal emulator program on the Personal Computer.
Utilize the program to access the Command Line Interface of your Cisco 1941 router while following How to Reset a Cisco Router to Factory Default.
In the CLI page of your wireless access point, enter the commands below to delete the current configuration.
router# write erase
Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
Proceed with reload? Press Enter key
Would you like to enter the initial configuration dialog? [yes|no] no Enter key
Do you want to save the configuration of the AP? [yes|no] no Enter key
Now, the default settings will get restored on your Cisco 1941 router.
How to Reset Cisco 2600 Router Password
The guidelines on how to reset the password in the Cisco 2600 are listed below.
Insert a Personal Computer or terminal to the console or AUX port located on your Cisco 2600 router.
If you are able to access your wireless access point, enter show version at the prompt and then configure the configuration settings.
Make use of the Power Switch to power Off the Cisco 2600 router. Now, switch your access point On.
Make sure to tap the Break button on the terminal keyboard within a minute to put the network router to the ROMmon mode.
Type confreg 0*2142 at the rommon > 1 prompt dialog box to start booting from FLASH.
Enter reset at the rommon > 2 prompt. The Cisco 2600 network router will reboot.
Type NO for all the setup questions that appear on the screen. Else, press the Ctrl and C buttons to skip the initial setup process.
Once the Router > prompt window appears, enter enable while following How to Reset Cisco 2600 Router Password.
To copy the Non Volatile Random Access Memory into memory, type copy startup-config running-config or configure memory.
Enter show running-config and mention the configure terminal. Mention enable secret and type a password that you can remember.
On every interface that you wish to utilize, issue the no shutdown command.
Exit the configuration mode by pressing the Ctrl and Z buttons.
The Hostname# instruction window opens on the screen for Cisco Wifi Router Reset.
Save the changes by entering copy running-config startup-config or write memory to reset by following how to reset the cisco router.
How to Reset Cisco 2800 Router
Resetting the Cisco 2800 router is generally carried out to bring the settings to its default. The procedure for resetting the Cisco 2800 network router is as follows,
All the network routers include a web-based setup page that lets users set up advanced properties and customize settings.
Before you open the Configuration page, make sure that the Cisco 2800 router is powered On.
Ensure that your Personal Computer is linked to the router.
Launch a browser such as Safari or Google Chrome on your device.
Enter the Cisco 2800 router’s IP address in the search bar while proceeding.
Tap Enter on your keyboard while following How to reset cisco 2800 router.
Now, go to the rear side of your Cisco 2800 router and press the Reset button on it for at least thirty seconds.
A new dialog box will appear on the computer that instructs you to enter the username and the password.
Type admin as the Password and the Username, and select the OK button by following How to Reset the Cisco Router.