Get Complete Netgear n600 Reset Router Guide
To perform Netgear N600 reset router, find the reboot or restore button. Usually, the Reset button is located on the back of the router. Connect the router to the power cord. Use a pen tip or sharp object to press and hold the button until the LED blinks. It takes a few seconds for the reset process to complete.
- Reset Netgear N6OO Wireless Router
How to Reset Netgear Router N600
Netgear n600 wireless router has the reset button on its rear.
Make use a pen tip or paperclip to press the button.
Hold the button until the Power LED light blinks.
Wait while the router restores to factory defaults for Netgear n600 Reset.
It will automatically restart.
Ensure that there is a proper connection between the router and the modem.
The power cord must be turned on.
You can also reset using the web browser. Make sure the computer is connected to the same network as the router.
- “Backup settings.” In the revert to factory default settings option, click ‘Erase.’
The reset process is now initiated.
How to Reset Netgear N600 Router to Factory Settings
In the Netgear N600 router, there are two ways to reset the router to factory settings.
The first method is to reset using the Reset button.
Turn on the router, and insert a tip of the pen in the reset button. The power button LED light will blink. Ensure that the power cord is connected correctly to the router.
The second method for resetting the router can be carried out using the Router admin panel.
Open a web page and enter the IP address in the address bar.
Type the user name and password.
Click on the “Login” button while following How to Reset Netgear Router N600.
Select the Backup settings from the left.
- “Revert to factory default settings.” Click “Erase.”
Wait for a few seconds for your router to update.
Now the router will reboot by doing How to Reset Netgear N600 Router to Factory Settings.
You can also reset using the admin router panel.
Enter the admin name and password in the Login page. Generally, the default admin name and password will be printed on the label attached to the router panel. You can change the default password to a new one. The password must be strong and lengthy.
- Backup Settings option. Go to the Revert to factory default settings section and select the Erase option for Netgear n600 Reset while following How to Reset Netgear N600 Router to Factory Settings guide.
The reboot process takes a few seconds. If you are not able to reset the router, then check the connectivity between the router and computer. Remove the connected cables and try to reset the cable connection while following How to Reset Netgear Router N600.
To know more about the Netgear N600 router, you can make use of the instruction manual provided by the manufacturer.
How to Reset Password on Netgear N600 Wireless Router.
Open a web browser. Type In the address www.routerlogin.net in the address bar.
Now the Login window will open.
Click the Cancel button and then type the serial number of the router. The serial number of your router is printed on the product label.
Click the Continue button during How to Reset Password on Netgear N600 Wireless Router.
A screen will pop up requesting you to answer the security questions.
Enter the appropriate answers to the security questions and click the Continue button. Now a screen will display prompting you to reset the router password.
Key in your new password and then confirm it.
You can now set new security questions for logging into the setup page. Click the Next button for Netgear n600 Reset router.
Ensure that your password has been reset successfully.
Click the Login button on completing How to Reset Password on Netgear N600 Wireless Router.
You can now log into the router admin page using the new password.
Netgear N600 Setup
Plug the modem to the Internet port of your Netgear n600 router.
Connect your modem to any of the four LAN ports available on the Personal Computer.
Switch Off the system, Netgear n600 router, and the modem for Netgear N600 Setup.
After a few minutes, power On all the devices and wait until the booting process gets completed.
Launch any browser such as Chrome or Safari.
In the address field, type the default IP address of your Netgear n600 router.
- 192.168.1.1 or 192.168.0.1. for Netgear N600 Setup
The IP address generally is
Press the Enter button. Now you will be asked to mention the login details.
By default, the password is password and the username is admin.
Make sure you type the username and the password correctly as they are case sensitive.
- Setup Wizard option. A screen opens on your desktop for Netgear N600 Setup.
Select the Yes button and then click on the Next option.
The Setup Wizard detects the mode of Internet connectivity.
Choose Next. Your Netgear n600 access point saves the settings.
To ensure that you are linked to the network, choose Router Status under the Maintenance menu.
How do I Reset my Netgear N600?
Find the Reset button; it is generally present at the rear of your Netgear n600 router.
Place a sharp paper clip or pin into the recess of the reset button.
Now, tap and hold the Reset button gently for about seven to eight seconds.
The Power lamp on your Netgear n600 router will start blinking.
Release the Reset button and the Netgear n600 router will reboot.
After the reset process is finished, the Power light will glow in a solid white or green color.
Now, set up and configure the router by following How to Reset Netgear Router N600.
Turn Off the Netgear n600 router and your modem for Netgear n600 Reset.
Make use of an Ethernet cord to link your modem to the Internet port on the Netgear n600 router.
Utilize another Ethernet cord to connect your PC to the LAN port on the access point.
Power On your router, open a browser, and then log into your router’s page.
Select the Advanced tab and choose Setup Wizard. Click on the Yes button.
After the Internet connectivity is detected, select Next.
How do you reset your router to factory settings?
Resetting the router will delete all the customized settings.
The access point’s username and the password will be restored to its factory default values as mentioned in the label.
All the Wireless Fidelity settings such as the Service Set Identifier name and the password will get deleted.
The wireless network cannot be accessed until you configure your Netgear n600 router.
Make sure to update all the devices that use the customized network settings.
To reset the access point to the default factory settings, follow How to Reset Netgear Router N600 procedure given here.
Go to the rear side of your router and locate the Reset button on it for Netgear n600 Reset.
With your router switched On, utilize the sharp end of a paper clip or pin to long press and hold the Reset button.
Now, release the Reset button after fifteen seconds.
Wait until the network router fully resets and powers On completely.
How do I log into my Netgear n600 router?
You can access the wireless setting only after logging into the Configuration web page of your Netgear n600 router.
The instructions on how to sign into the Netgear n600 wireless access point are as follows.
Open the web browser on the computer, laptop, or mobile device that is connected to the Netgear n600 router.
Some of the common browsers include Mozilla Firefox, Google Chrome, Microsoft Internet Explorer, and more.
In the search field, enter www.routerlogin.com or www.routerlogin.net and then tap the Enter button.
Else, click on the Search button.
The browser might open a prompt that says that the connectivity is not secure.
In the router login dialog box, type the default username and also the key.
The entries must be entered properly as they are case sensitive.
Select the Log In option or click on the OK button.
The Basic Home Page displays on your Personal Computer; the process ends with this.
Where is the WPS button on the Netgear n600?
The WPS button is needed for setting up the wireless connection.
The WPS button is present on top of the Netgear n600 router; it is usually represented as a two-sided arrow mark.
The Netgear n600 WPS button can be used for configuring and connecting a device to the existing network.
Press the WPS button that is found on your Netgear n600 wireless router.
Release the button after a few seconds.
Now you have to press the WPS button on the other device such as a printer that you want to connect to the network.
Ensure that the lights on the Netgear n600 router are flashing.
The lamp might blink if the Netgear router has successfully configured the settings.
It might also flicker if the SSID name and the password are turned On.
Now, check if the Netgear router is connected to the wireless network.
Netgear n600 default password
The default password for the Netgear n600 router is password.
If you want to alter the admin password of your Netgear n600 access point, go with the procedure given here.
From your Personal Computer or wireless device that is associated with the wireless network, open a web browser.
Enter the manufacturer’s link into the search field to open the Login dialog box on the computer.
Type the default username and the security key of your Netgear n600 router.
The Basic Home Page appears on your desktop.
Choose the Advanced tab, select Administration, and then click on the Set Password button.
Type the old password. Create a new password and then reenter it again.
If you want to retrieve the security key in the future, mark on the Enable Password Recovery checkbox.
Now, click the Apply button.
To modify the password of the Wireless Fidelity network, open a browser and type the Netgear n600 router’s IP address.
After you type the username and the password, click the OK button.
Select the Wireless option on the Basic Home Page.
Enter your new SSID name and its security key in their correct fields, and choose the OK button to complete Netgear n600 Reset.