Belkin Router Reset
The Belkin routers are efficient for the hardware reset and if you find any issues with the default settings of the router, resetting it is the only solution. You can delete the default settings,and the router will be back to the current factory settings. The Belkin router reset can be done with the help of the reset button on the router, followed by simple steps.
How to Reset Belkin router
First, make sure that the router is powered on.
Now, turn the router and check for the reset button.
The Belkin router reset button would be red in color and will be highlighted with the word Reset.
Then, make use of a bent paper clip or any thin object to press the reset button.
Keep pressing the reset button for about 10 seconds.
After releasing the Reset button, the router will be set to the factory default settings.
Now, change the settings or make use of the same settings for Internet connectivity.
Factory Reset Belkin Router
Soft factory reset,
First, enter the router URL and login to the router as an administrator.
Navigate to the Administration section and then choose Advanced Settings.
Then, select Restore Factory Defaults to factory reset Belkin router.
Now, the router will reboot and restore to factory settings.
Check for the Reset button at the rear of the router.
- router setup is powered on to factory reset Belkin router.
Verify that the
Now, keep pressing and holding the reset button about 15 seconds to reset Belkin router.
It will take some time to restart and reset to factory settings.
Reset Belkin Router Password
To reset Belkin router password, follow the instructions given below.
First, connect your Belkin router to the computer using a LAN cable.
After that, launch a web browser on your computer, click anywhere in the search field, and type the 192.168.2.1 IP address.
Press the Enter button on your system’s control panel.
Click the Login button and type the current credentials in the given field.
If you are log into the Belkin router before, then leave the password field blank, and click the Submit button.
Click the Utilities tab, and select the Restore Factory Default option followed by the OK button.
Wait for the Belkin router reset process to complete.
After that, set the password by clicking the System Settings option in the same Utilities section.
Belkin Router Admin Password Reset
For Belkin router admin password reset, read and proceed with the guided instructions given below.
- Belkin router setup to begin the admin password reset process.
Switch on your
Locate the Belkin router Reset key on your Belkin router.
In most cases, the Reset button is located at the back of the router.
- Belkin router admin password reset.
Now, press & hold the Reset button for a maximum 15 seconds for
If the router automatically restarts, then it means the Belkin router is reset successfully.
After that, on your system, launch a web browser, and log into the Belkin router site using the 192.168.2.1 IP Address.
Do not type anything in the Password field. Provide your username in the required field, and click the Submit button.
After that, set a new password as per your wish on your Belkin router setup page.
Belkin Router Red Light After Reset
To fix the Belkin router red light after reset issue, perform the troubleshooting instructions given below.
Switch off your Belkin router, disconnect the power cable from it, and wait for a few seconds.
After that, reconnect the power cable to the Belkin router and check if the issue is resolved.
If the Belkin router red light after reset issue persists, then check your Internet connection.
If your Internet connection is weak or not stable, then disconnect and reconnect the modem.
If the problem is with your internet, then contact your Internet Service Provider (ISP), and fix the problem.
If the internet connection is good, but the Belkin router red light after reset issue persists, then contact the Belkin router support to fix it.
Belkin N300 ROUTER RESET
Follow the steps that are mentioned here to reset Belkin router.
Check if the Belkin router is turned on.
Unplug the router from the power supply while it is turned on.
Wait for a few minutes before plugging the router to the power supply.
Connect the router to the electrical outlet using the power cord.
The Belkin router reset process is now complete.
Belkin N450 ROUTER RESET
Refer to the Belkin router reset procedure that is specified here to reset the router.
You can either reset or restore the router using the Reset button.
Turn the Belkin N450 router to its backside and find the Reset button.
Press the Reset button once to initiate the reset Belkin router process.
Wait till the Belking N450 router reboots.
If you want to restore the settings to its default values, press the Reset button and hold it for 5 seconds.
After the restoration is complete, all the settings will be restored.
HOW TO RESET Belkin N600 ROUTER
The Belkin N600 router can be reset using the following guidelines.
Launch the frequently used Internet browser on your system.
Go to the search bar and type the IP address of the Belkin N600 router. Tap Enter.
Click the Login option present in the top part of the screen. Enter the username and tap Submit.
Select the Utilities option from the left pane of the window and choose the Restore Factory Default option.
Click the Restore Defaults button available on the next page.
Tap the OK button when the Warning message appears on your screen.
Once you choose Yes, the settings will be deleted, and the router will start functioning based on the default settings.
Configure the Belkin router settings again and connect devices to it after Belkin router reset.